Mar 03, 2008 Motherboard Manual. Seems more likely it is from the PCchips/Elpina/Amptron/PCw are group of manufacturers. Motherboard search engines can be. Mar 16, 1999 Elpina motherboards I would. I hope this is what I was looking for too. Was your board labeled Elpina-2 on the back or was it. Download 1 Elpina Motherboard PDF manuals. User manuals, Elpina Motherboard Operating guides and Service manuals.

• Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. • Table of Contents HARDWARE CONFIGURATION..

3 Key Features...3 Motherboard Layout (Model Code No. - 35893000XX).5 Jumper Settings..6 CPU Speed Selection..6 JP1, JP5 - System Bus Frequency..6 JP3 - CMOS Clear.. 6 JP7 - Ratio of Processor Core to System Bus Frequency. • HARDWARE CONFIGURATION This motherboard is based on the Intel® 82443BX/ZX/VIA® VT82C693/693A chipset. The chipset is a highly integrated solution for a cost-effective and compact motherboard.

The motherboard supports SDRAM. Features on-board include super-I/O, Ultra DMA33, Ultra DMA66 (for South Bridge VT82C596B Ver. • • 2 ISA slots.

On-Board I/O • Two PCI fast IDE ports supporting up to 4 ATA2, Ultra DMA33 IDE HDDs, Ultra DMA66 IDE HDDs (for south bridge VT82C596B Ver. Only), CD-Roms, ZIP devices and LS-120 drives as boot drive.

• Motherboard Layout (Model Code No. - 35893000XX) The following diagrams show the relative positions of the jumpers, connectors, major components and memory banks on the motherboard. Warning: All connectors on board are labeled Pin “1” at one conner. Ribbon cables should always be connected with the red stripe on the Pin “1”. • Jumper Settings Warning: Please turn off AC power before installing and removing any device. If you can’t turn on system power, please clear CMOS and keyboard password(JP28). Teorema Di Taylor Pdf. Then try again This chapter explains how to configure the motherboard’s hardware.

Before using your computer, make sure all jumpers and DRAM modules are set correctly. • JP7 - Ratio of Processor Core to System Bus Frequency Ratio of System Ratio of System JP8, JP15- BIOS Program Voltage / BIOS Select JP15 Selection (1-2) (1-2) INTEL (1MB) (1-2) (2-3) MX (1MB) (2-3) (2-3) ATMEL/SST/Winbond (1MB) (2-3) (2-4) ATMEL/SST/Winbond (2MB) JP8 &. • Keyboard Password Power On (Only for ATX Power Supply) This motherboard provides a special security feature of keyboard password power on. The feature is enabled in Integrated Peripherals Menu of CMOS setup. There are two modes of operations.

(1) Single Key Turn On - if you set a single key password, the system will turn on immediately after you press the password key (440BX/ZX only). • Memory Configuration You can install up to 256MB(SDRAM) or 512MB(Registered SDRAM) of memory in the motherboard DIMM sockets.

The board has DIMM sockets arranged as banks 1, and 2. You can install DIMMs in any of the two banks, and use different size DIMMs in different banks. • Installing the Processor • Unpack the CPU and identify the pin 1 corner of the CPU. • Match pin 1 of the CPU with pin 1 of the CPU socket. The pin 1 corner of the CPU socket is designated by a small triangle printed on the motherboard. • BIOS SETUP This chapter discusses Award’s Setup Program built into the ROM BIOS. The Setup Program allows users to modify the basic system configuration.

This special information is then stored in battery-backed RAM, which retains the setup information when the power is turned off. Starting Setup The Award BIOS is immediately activated when you turn on the computer. • ROM PCI/ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE. STANDARD CMOS SETUP CPU SPEED SETTING BIOS FEATURES SETUP INTEGRATED PERIPHERALS CHIPSET FEATURES SETUP SUPERVISOR PASSWORD POWER MANAGEMENT SETUP USER PASSWORD PNP/PCI CONFIGURATION SETUP IDE HDD AUTO DETECTION LOAD BIOS DEFAULTS SAVE &. • Integrated This section page includes all the items of IDE hard drive Peripherals and Programmed Input / Output features.

Supervisor / Changes, sets, or disables password. It allows you to limit User Password access to the system and the Setup Program.